AEROX SOLDERING STATION 150HS EU 220-240V

Introducing from AEROX the awesome 150HS Soldering Station.

A fully adjustable quality soldering station at a great price.

This version is the 220-240V version with European plug.

Features

- 150W of power!
 Fully adjustable temperature from 100 to 500 Degrees C.
- Super fast heat up.
- Fantastic tip cleaning solutions.
- Internal solder roll holder - Never lose your solder. Allows solder to be dispensed through the front of the unit so always ready to use. (Not pictured)
- Available with 3 different plugs for UK and Europe (220-240V) and USA (110-120V). 
- Large bevel tip included, optional fine point and chisel tips available.
- Optional  'Helping Hands' to assist when soldering.

Specifications

Model - 150HS
Power - 150W
Input Voltage -  230VAC (UK/EU) (50-60Hz)
Temp. Range - 100-500℃(212-932℉)
Temp. Stability - ±2℃(±4℉) {>200℃(400℉)}
Temp. Compensation - ±50℃(±90℉)
Temp. Display - Digital
Tip to ground impedance - <0.1Ω
Tip to ground voltage - <2mV
Heater - T60 integrated PTC ceramic heater
Cable length - Power cord: 90cm Handle cable: 1.2m
Dimensions main unit: 80 x 184 x 142mm handle: 24.5 x 224mm
Net weight 516g

Aerox TC Droop Gauge & Disks

Aerox TC Droop Gauge & Disks

Introducing the new Aerox droop gauge set for 1-10th Touring cars.

A new universal way to take the confusion out of measuring droop across different chassis manufacturers.

Droop is a measurement used to define the point at which the tyre leaves contact with the ground. It can be a very powerful tool to quickly change the behaviour of a car. Measuring droop to the axle centre is the most accurate way of doing so, as it eliminates any potential discrepancy in the symmetry of suspension components. This method is also the only correct way to quickly and easily compare droop across different cars, without the need to
account for any differences in car design.

Using the Aerox system is simple. Fasten the droop wheels on to one pair of axles. The chassis sits on the 10mm droop blocks. The droop gauge is used to measure to the lowest part of the droop wheel. The reading from the gauge is the distance from chassis underside to the centre of axle. Repeat for the other pair of axles.

For easy storage and transportation, the M4 grub screw is inserted into the side of the droop gauge so that it protrudes
equally out of both sides. This is then locked off with the M3 grub screw from the underside. The droop wheels then attach to the droop gauge via the M4 grub screw for safe storage.

Aerox TC Droop Gauge Set

Aerox TC Droop Gauge Set

Introducing the new Aerox droop gauge set for 1-10th Touring cars.

A new universal way to take the confusion out of measuring droop across different chassis manufacturers.

Droop is a measurement used to define the point at which the tyre leaves contact with the ground. It can be a very powerful tool to quickly change the behaviour of a car. Measuring droop to the axle centre is the most accurate way of doing so, as it eliminates any potential discrepancy in the symmetry of suspension components. This method is also the only correct way to quickly and easily compare droop across different cars, without the need to
account for any differences in car design.

Using the Aerox system is simple. Fasten the droop wheels on to one pair of axles. The chassis sits on the 10mm droop blocks. The droop gauge is used to measure to the lowest part of the droop wheel. The reading from the gauge is the distance from chassis underside to the centre of axle. Repeat for the other pair of axles.

For easy storage and transportation, the M4 grub screw is inserted into the side of the droop gauge so that it protrudes
equally out of both sides. This is then locked off with the M3 grub screw from the underside. The droop wheels then attach to the droop gauge via the M4 grub screw for safe storage.



As a starting point, we recommend a droop gauge value of:

Tarmac/Asphalt
Front: 22 - 23mm
Rear: 21 - 22mm

Carpet
Front: 22.5 - 23.5mm
Rear: 21.5 - 22.5mm

Aerox Touring Car Body Rear Stiffeners

Aerox Touring Car Body Rear Stiffeners

Introducing these Touring Car body stiffeners from Aerox.

Designed to improve the the bodyshells stiffness and therefore it's form at high speeds, these stiffeners are ideal when using the new Ultra Light Weight bodyshells.

With Centre of Gravity in mind, these have been designed to be as light as possible.  Weighing in at just 1.1g (without tape) for the rear.

Side stiffeners are also available AX035.

Important: In some cases super glue such as CR522 must be used to fix the Carbon Rods into the brackets. This is best achieved after installation onto the bodyshell.

Supplied with double sided tape.

Aerox Touring Car Body Side Stiffeners

Aerox Touring Car Body Side Stiffeners

Introducing these Touring Car body stiffeners from Aerox.

Designed to improve the the bodyshells stiffness and therefore it's form at high speeds, these stiffeners are ideal when using the new Ultra Light Weight bodyshells.

With Centre of Gravity in mind, these have been designed to be as light as possible. Weighing in at just 1.3g (without tape) for the sides.

Rear stiffeners are also available AX036.

Important: In some cases super glue such as CR522 must be used to fix the Carbon Rods into the brackets. This is best achieved after installation onto the bodyshell.

Supplied with double sided tape.

Aerox Trident Wing LD3 - 1.0mm Clear

Aerox Trident Wing LD3 - 1.0mm Clear

The kit wing for the Cougar LD3 the Trident is suitable for all 1/10th 2WD and 4WD buggies.

1.0mm thick.

6.5 inch wide the Trident is a great all rounder.

Made from polycarbonate and supplied clear.

After-Run Oil 60ml

After-Run Oil 60ml
de olie die je gebruikt na het rijden voor een nito motor

Air filter (complete with rubber base & foam insert), TRX4060

Air filter (complete with rubber base & foam insert), TRX4060

Air filter (foam insert only), TRX4061

Air filter (foam insert only), TRX4061

Air Filter 1:8 Star Shape absima

Aktivatorspray 300ml

Aktivatorspray 300ml

Sekondenlijm is in enkele sekonden hard.
Ideaal om zeer snel te bouwen.

Artikel nummer: 806062

EAN: 4080606200000

ALLOY CASTOR POINTER - MI9 (PR)

This castor gauge set is used to accurately set castor on the Mi9 when using kit upper links. This is not required with the fixed
castor type upper wishbone found on the Mi9 ‘Upper wishbone conversion.’

It will work with Arrowmax 4d system, Arrowmax Black and Gold, Arrowmax silver system and new and old Hudy systems.

ALLOY OFFSET SERVO ARM 25T - FUTABA

Black Alloy Servo Arms from CORE RC. Available in the popular 23T and 25T splines these alloy offset servo arms are ideal for a variety of vehicles and should be very popular for the Mi5evo for those who want to square up the servo/electronics installation.

 

Multi position pick up and with lightweight clamping screw.

Multi hole positions, 16mm, 19mm, 22mm and 25mm.

Alu 7075 T6 wheel hubs offset +1.50mm 1:10 (2)ABSIMA

● Absima sticker sheet
 

Alu 7075 T6 wheel hubs offset +2.00mm 1:10 (2)ABSIMA

● Absima sticker sheet
 

Alu High-Speed Brushless Fan (Motor 30*30mm) 28.000RPM Item no.: 2310051

Alu High-Speed Brushless Fan (Motor 30*30mm) 28.000RPM

Item no.:  2310051

High-speed aluminum fan in a classy design.
The fan's aluminum housing ensures optimum heat dissipation to prevent the speed controller from overheating. The fan's brushless motor provides up to 28,000 rpm (8.4V) - values that can never be achieved with a coreless motor.
 
SPECS:

• T6 Aluminum
• Brushless Motor
• Silicon Cable
• Reverse Polarity Protected
• Plug: JST / BEC 2Pin for RX/Bat. connection
• Wire Length: 180mm
• Speed: 28.000RPM
• Input Voltage: 5-8.4V (2S LiPo)
• Current: 0.6A
• Color: Black Housing with Silver Cuttings
• Installation hole spacing: 25mm
• Size: 30 x 30 x 10mm
• Weight: 15g

Alu wheel hubs 12 HEX offset 6MM ORANGE 4STUKS

Alu wheel hubs 12 HEX offset 7MM BLAUW 4STUKS
INCL BOGING

Alu wheel hubs 12 HEX offset 7MM BLAUW 4STUKS

Aluminium Tool voor Band Dynamische Balanceren 12Mm/17Mm Adapter Voor 1/10 1/8

super mooie tool om te kijken of je onbalans in je wielen heb en deze mooi stil te kunnen maken.
Materiaal: metaal aluminium
adapter 12mm 17mm
Toepassing op alle 12mm 17mm hex  banden

Aluminium Wing Washers 11.5mm - Black/Gold (pr)

Aluminium Wing Washers 11.5mm - Black/Gold (pr)

Black and Gold wing washers from MonkeyKingRC. Small 11.5mm diameter and very lightweight. Gives the modern lightweight wings more support. Neat and cool look.